surface mount voltage range 50 to 1000 volts current 1.0 ampere rectron semiconductor technical specification features * ideal for surface mounted applications * low leakage current * metallurgically bonded construction * mounting position: any * weight: 0.057 gram * epoxy : device has ul flammability classification 94v-0 maximum ra tings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load.for capacitive load, derate current by 20%. electrical characteristics (at t a = 25 o c unless otherwise noted) HFM101W thru hfm108w smx maximum ratings (at t a = 25 o c unless otherwise noted) high efficiency silicon rectifier notes : 1. test conditions: i f =0.5a, i r =-1.0a, i rr =-0.25a. 2. measured at 1 mh z and applied reverse voltage of 4.0 volts. dimensions in inches and (millimeters) 2005-10 ratings maximum recurrent peak reverse voltage maximum rms volts maximum dc blocking voltage maximum average forward current at t a = 50 o c peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (jedec method) typical junction capa citance (note 2) operating and storage temperature range symbol v rrm v dc i o i fsm c j t j , t stg v rms volts volts volts amps 1.0 30 15 -65 to + 150 amps pf 0 c units 12 maximum dc reverse current at characteristics v f symbol i r trr units uamps nsec maximum full load reverse current, full cycle average t a = 55 o c maximum forward voltage at 1.0a dc volts 5.0 50 maximum reverse recovery time (note 1) rated dc blocking voltage 50 uamps 1.0 1.7 75 5035 50 100 70 100 300210 300 400280 400 800560 800 1000 700 1000 200140 200 600420 600 1.3 @t a = 25 o c @t a = 125 o c 100 uamps mechanical data HFM101W hfm102w hfm104w hfm105w hfm107w hfm108w hfm103w hfm106w HFM101W hfm106w hfm103w hfm107w hfm108w hfm104w hfm102w hfm105w 3. fully rohs compliant,100% sn plating (pb free). .209 (5.31).185 (4.70) .091 (2.31).067 (1.70) . 110 (2.79) . 086 (2.18) .011 (0.28).007 (0.18) .180 (4.57).160 (4.06) .059 (1.50).035 (0.89) .010 (0.25).008 (0.20) .071 (1.80 ) .051 (1.30 ) downloaded from: http:///
rectron rating and characteristic curves ( HFM101W thru hfm108w ) fig. 1 - test circuit diagram and reverse recovery time characteristic 50noninductive 10noninductive d.u.t 25 vdc(approx) ( - ) ( - ) ( + ) ( + ) 1non- inductive oscilloscope (note 1) pulse generator (note 2) notes: 1 rise time = 7ns max. input impedance = 1 megohm. 22pf. 2. rise time = 10ns max. souce impedance = 50 ohms. trr +0.5a 0 -0.25a -1.0a 1cm set time base for10/20 ns/cm fig. 2 - typical forwardcurrent derating curv e average forward curent, (a) ambient temperature ( ) 2.01.0 0 25 50 75 100 125 150 175 0 single phasehalf wave 60hz resistive or inductive load fig. 4 - typical instantaneous forward characteristics instantaneous forward current, (a) instantaneous forward voltage, (v) 10 1.0 .1 .01 .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 pulse width = 300us1% duty cycle t j = 25 hfm106w~hfm108w HFM101W~hfm103w hfm104w~hfm105w fig. 3 - typical reverse characteristics instantaneous reverse current, (ua) percent of rated peak reverse voltage, (%) t j = 25 t j = 100 t j = 150 100 10 1.0 .1 .01 40 0 20 60 80 100 120 140 fig. 6 - typical junction capacitance junction capacitance, (pf) reverse voltage, ( v ) 200100 6040 20 10 64 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 HFM101W~hfm105w hfm106w~hfm108w t j = 25 fig. 5 - maximum non-repetitive forward surge current peak forward surge current, (a) number of cycles at 60hz 7060 50 40 30 20 10 0 1 2 5 10 20 50 100 8.3ms single half sine-wave(jedec method) downloaded from: http:///
mounting pad layout rectron 0.060 min.(1.52 min.) 0.052 min.(1.32 min.) 0.220 0.094 max.(2.38 max.) (5.58) ref dimensions in inches and (millimeters) downloaded from: http:///
|
